Advertisement

There's no such thing as a stupid question, but they're the easiest to answer.
Login
Search

Advertisement

Networking Networking
Search Search
Search for:
Tech Support Guy > > >

help with dlink wireless router on hughesnet sat internet


(!)

td727's Avatar
td727 td727 is offline
Junior Member with 4 posts.
THREAD STARTER
 
Join Date: Aug 2008
15-Jan-2010, 12:28 AM #1
help with dlink wireless router on hughesnet sat internet
am trying to hook up dlink di-624 wireless router to a hughesnet satalite internet conection. hughesnet modem HN9000. have internet connection without router. when i hook up it shows router connectivity but no internet. have done all normal start up precedures. normal auto connect is not working. am not sure on the procedures for determining my sat modem ip address. but have tryed "MANY" different config. i know this is just a matter of knowing whick addresses go where and in the right order but i am at a loss!! please help. will return any info needed.basics as follows.pc machine with xp, latest service packs installed. d-link DI-624 wireless router, hughesnet HN 9000 modem.
warrior19's Avatar
warrior19 warrior19 is offline
Senior Member with 984 posts.
 
Join Date: Oct 2009
Location: London, UK
Experience: Advanced
15-Jan-2010, 06:50 AM #2
To help connect the PC to the HN9000 directly and try to establish the Default Gateway IP Address using the commands below:

Hold the Windows key and press R, then type CMD to open a command prompt.

In the command prompt window that opens, type type the following commands:

IPCONFIG /ALL. This should work for any Windows version. The IPCONFIG /ALL display will provide a wealth of useful information for debugging your network connection.

Please post the info from this command both directly attached to the cable modem and again when attached via the DI-624 router?

Connect the HN9000 to the WAN port of the DI-624. Connect your PC with an ethernet cable to any one of ports 1 to 4.

Download the Product Manual at

http://www.dlink.com/products/?tab=3...624&rev=DI-624.

Page 12 of the Product Manual describes how to access the configuration but I think you already know?

Page 14 describes selecting Dynamic IP Addressing which works for most Cable Modems. This should just assign the router appropriate addressing and you should test internet connection with your PC in ports 1 to 4?

Page 15 describes Static IP addressing. You would need to check with Hughesnet as your ISP as to whether they have setup your service with Static IP addressing?

Finally on page 18 ensure you have DHCP enabled on the router and assign an IP address range like suggested 192.168.0.2 to 192.168.0.199.

In LAN setup the router should already be assigned IP address 192.168.0.1 and subnet mask 255.255.255.0

With all of this setup and config saved it should connect to the internet ok from ports 1 to 4.

Once you have it working then try setting up wireless on the DI-624 but try withb wires first to make sure internet connects.

GOO LUCK!
warrior19's Avatar
warrior19 warrior19 is offline
Senior Member with 984 posts.
 
Join Date: Oct 2009
Location: London, UK
Experience: Advanced
15-Jan-2010, 06:53 AM #3
To be clear try from DI-624 manual Page 14, 17 and 18 as default way to get this working. Only worry about Static IP on page 17 and asking Hughenet if this first way dfoes not work.
As Seen On

BBC, Reader's Digest, PC Magazine, Today Show, Money Magazine
WELCOME TO TECH SUPPORT GUY!

Are you looking for the solution to your computer problem? Join our site today to ask your question. This site is completely free -- paid for by advertisers and donations.

If you're not already familiar with forums, watch our Welcome Guide to get started.


(clock)
THIS THREAD HAS EXPIRED.
Are you having the same problem? We have volunteers ready to answer your question, but first you'll have to join for free. Need help getting started? Check out our Welcome Guide.

Search Tech Support Guy

Find the solution to your
computer problem!




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools


WELCOME
You Are Using: Server ID
Trusted Website Back to the Top ↑