1. Computer problem? Tech Support Guy is completely free -- paid for by advertisers and donations. Click here to join today! If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members.

Automatic get Restart

Discussion in 'Windows XP' started by kuzhanthaivelu, Apr 27, 2009.

Thread Status:
Not open for further replies.
Advertisement
  1. kuzhanthaivelu

    kuzhanthaivelu Thread Starter

    Joined:
    Oct 9, 2008
    Messages:
    123
    Hai Everybody ,

    I have an Desktop with XP Professional Operating System. Recently a two days before get automatic restarted when i had been working the same.
    Anybody can give the solution for resolve my problem. I am fear about whether my data will get loss.

    Thanks in advance.
     
  2. Jack Hackett

    Jack Hackett

    Joined:
    Nov 19, 2006
    Messages:
    1,938
    Right click on My Computer, select Properties
    Click on Advanced tab
    under Startup and Recovery click Settings button
    under System Failure , Untick Automatically Restart - OK

    Next time your system crashes you should be presented with a Blue Screen with an error message, make a note of the error code and any file names mentioned and post those back here
     
  3. kuzhanthaivelu

    kuzhanthaivelu Thread Starter

    Joined:
    Oct 9, 2008
    Messages:
    123
    Yes, I got an Stop error message as 0*0000007A.

    and messages also as Kernal inpage error also display below for error code.

    What can i do now?
     
  4. Jack Hackett

    Jack Hackett

    Joined:
    Nov 19, 2006
    Messages:
    1,938
    Stop 0x0000007A or KERNEL_DATA_INPAGE_ERROR

    The Stop 0x7A message indicates that a page of kernel data was not found in the paging (virtual memory) file and could not be read into memory. This might be due to incompatible disk or controller drivers, firmware, or hardware.

    Frequently, the cause of this error can be determined from the second parameter, the I/O status code. Some common status codes are:

    # 0xC000009A, or STATUS_INSUFFICIENT_RESOURCES, indicates a lack of nonpaged pool resources
    # 0xC000009C, or STATUS_DEVICE_DATA_ERROR, indicates bad blocks (sectors) on the hard disk
    # 0xC000009D, or STATUS_DEVICE_NOT_CONNECTED, indicates defective or loose data or power cables, a problem with SCSI termination, or improper controller or disk configuration
    # 0xC000016A, or STATUS_DISK_OPERATION_FAILED, indicates bad blocks (sectors) on the hard disk
    # 0xC0000185, or STATUS_IO_DEVICE_ERROR, indicates improper termination, defective storage controller hardware, or defective disk cabling, or two devices attempting to use the same resources.

    Possible Resolutions:

    # Stop 0x7A can be caused by bad sectors in the virtual memory paging file, disk controller error, virus infection, or memory hardware problems. In extremely rare cases, depleted nonpaged pool resources can cause this error. If the first and third parameters are zero, the stack signature in the kernel stack is missing, an error typically caused by defective hardware. If the I/O status is 0xC0000185 and the paging file is on a SCSI disk, check for cabling and termination issues. An I/O status code of 0xC000009C or 0xC000016A indicates that the requested data could not be found. You can try to correct this by restarting the computer. If a problem with disk integrity exists, Autochk, a program that attempts to mark bad disk sectors as defective so that they are not used in the future, starts automatically. If Autochk fails to run, you can manually perform the integrity check yourself by following the instructions to run Chkdsk provided in "Stop 0x00000024 or NTFS_FILE_SYSTEM" earlier in this appendix.
    # Another cause of Stop 0x7A messages is defective, malfunctioning, or failed memory hardware, such as memory modules, Level 2 (L2) SRAM cache, or video adapter RAM. If you added new hardware recently, remove and replace it to determine if it is causing or contributing to the problem. Run diagnostics software supplied by the system manufacturer to determine if the component has failed.
    # Check the hardware manufacturer's Web site for updates to disk adapter firmware or drivers that improve compatibility. Verify that your disks and controller support the same set of advanced features, such as higher transfer rates. If necessary, select a slower transfer rate if an update is not yet available. Consult your hardware or device documentation for more information.

    Important

    - You can install disk controller drivers not present on the Windows XP Professional operating system CD by responding to the following prompt shortly after starting Setup:
    - Press F6 if you need to install a third party SCSI or RAID driver.
    - Press F6, and when prompted, provide the appropriate storage controller driver (ATA or SCSI) supplied by the manufacturer.

    # The problem might also be due to cracks, scratched traces, or defective components on the motherboard. If all else fails, take the system motherboard to a repair facility for diagnostic testing.
     
  5. kuzhanthaivelu

    kuzhanthaivelu Thread Starter

    Joined:
    Oct 9, 2008
    Messages:
    123
    Thank you for your information Jack Hackett.

    But i cannot confirm which information i would follow to resolve my problem.

    If you donot mind can you give a clear solution for that.

    :)
     
  6. Sponsor

As Seen On
As Seen On...

Welcome to Tech Support Guy!

Are you looking for the solution to your computer problem? Join our site today to ask your question. This site is completely free -- paid for by advertisers and donations.

If you're not already familiar with forums, watch our Welcome Guide to get started.

Join over 733,556 other people just like you!

Thread Status:
Not open for further replies.

Short URL to this thread: https://techguy.org/822173

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice