1. Computer problem? Tech Support Guy is completely free -- paid for by advertisers and donations. Click here to join today! If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members.

I usaully can do this kind of stuff but im stumped! I cant acess my router!

Discussion in 'Networking' started by jadenz123, Nov 23, 2011.

Thread Status:
Not open for further replies.
  1. jadenz123

    jadenz123 Thread Starter

    Joined:
    Nov 23, 2011
    Messages:
    2
    I connected a qwest modem to my computer and can easliy acsess it by type in 192.168.0.1 in the adress bar, but i pluged in a TRENDnet router to my qwest modem and when i type in 192.168.10.1 it just cannot display webpage! (For this router its 192.168.10.1 not 192.168.1.1!!)
     
  2. etaf

    etaf Moderator

    Joined:
    Oct 2, 2003
    Messages:
    65,408
    First Name:
    Wayne
    you connecting two routers together - if you just have the trendnet connected to power and not to the other quest router - can you login ?
    whats the exact model of the trendnet

    once you manage to log into the trendnet - to connect two routers together see below

    ------------------------------------------------------------------------

    Connecting two (or more) SOHO broadband routers together

    Connecting two (or more) SOHO broadband routers together
    Shamelessly stolen from a John Will Post :)

    Note: The "primary" router can be an actual router, a software gateway like Microsoft Internet Connection Sharing, or a server connection that has the capability to supply more than one IP address using DHCP server capability. No changes are made to the primary "router" configuration.

    Configure the IP address of the secondary router(s) to be in the same subnet as the primary router, but out of the range of the DHCP server in the primary router. For instance DHCP server addresses 192.168.0.2 through 192.168.0.100, I'd assign the secondary router 192.168.0.254 as it's IP address, 192.168.0.253 for another router, etc.

    Note: Do this first, as you will have to reboot the computer to connect to the router again for the remaining changes.

    Disable the DHCP server in the secondary router.

    Setup the wireless section just the way you would if it was the primary router, channels, encryption, etc.

    Connect from the primary router's LAN port to one of the LAN ports on the secondary router. If there is no uplink port and neither of the routers have auto-sensing ports, use a cross-over cable. Leave the WAN port unconnected!

    This procedure bypasses the routing function (NAT layer) and configures the router as a switch (or wireless access point for wireless routers).

    For reference, here's a link to a Typical example config using a Netgear router

    ------------------------------------------------------------------------
     
  3. dlsayremn

    dlsayremn

    Joined:
    Feb 9, 2008
    Messages:
    1,862
    Did you do an ipconfig /all with the Trendnet router connected to the computer to be sure the gateway IP is 192.168.10.1?
     
As Seen On
As Seen On...

Welcome to Tech Support Guy!

Are you looking for the solution to your computer problem? Join our site today to ask your question. This site is completely free -- paid for by advertisers and donations.

If you're not already familiar with forums, watch our Welcome Guide to get started.

Join over 733,556 other people just like you!

Loading...
Similar Threads - usaully kind stuff
  1. tyka88
    Replies:
    1
    Views:
    437
Thread Status:
Not open for further replies.

Short URL to this thread: https://techguy.org/1028174

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice