1. Computer problem? Tech Support Guy is completely free -- paid for by advertisers and donations. Click here to join today! If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members.

Linksys WRT54GS Wireless Connection No Longer Works

Discussion in 'Networking' started by Marathonman7777, Aug 9, 2009.

Thread Status:
Not open for further replies.
Advertisement
  1. Marathonman7777

    Marathonman7777 Thread Starter

    Joined:
    Aug 9, 2009
    Messages:
    3
    I have a Linksys WRT54GS router where the wireless connection stopped working on the laptop. Connection works fine when connected by wire. I have reset router and updated firmware and nothing is working. What can I do?
     
  2. JohnWill

    JohnWill Retired Moderator

    Joined:
    Oct 19, 2002
    Messages:
    106,418
    Do you see the wireless network at all from the laptop? Can the laptop see other wireless networks?
     
  3. Marathonman7777

    Marathonman7777 Thread Starter

    Joined:
    Aug 9, 2009
    Messages:
    3
    No, it finds no wireless networks.
     
  4. Curly

    Curly

    Joined:
    Apr 1, 2002
    Messages:
    1,249
    Are you sure that the wireless function of your router is turned on? You can verify this making sure that the WLAN light is lit on the front of the router and/or by accessing the modem's configuration menu.
     
  5. Marathonman7777

    Marathonman7777 Thread Starter

    Joined:
    Aug 9, 2009
    Messages:
    3
    Yes, it is on.
     
  6. JohnWill

    JohnWill Retired Moderator

    Joined:
    Oct 19, 2002
    Messages:
    106,418
    Well, I think my next step would be to reset the router to factory defaults and reconfigure. If that doesn't do it, the router's wireless capability may have died. I'm assuming you have moved the wireless machine in the same room to make sure you're easily within range, right?


    The following procedure should get you a connection with any broadband modem that is configured to use DHCP for the router connection, such as cable modems, and many DSL modems. If you require PPPoE configuration for the DSL modem, that will have to be configured to match the ISP requirements.

    Note that the wireless encryption and channel selection will have to be done after the basic wired connection is established, the first step is to get wired connections working.


    • Reset the router to factory defaults by holding the reset button down for 15 seconds with power on.
    • Turn off everything, the modem, router, computer.
    • Connect the modem to the router's WAN/Internet port.
    • Connect the computer to one of the router's LAN/Network ports.
    • Turn on the modem, wait for a steady connect light.
    • Turn on the router, wait for two minutes.
    • Boot the computer.

    When the computer is completely booted, let's see this.

    Hold the Windows key and press R, then type CMD (COMMAND for W98/WME) to open a command prompt:

    NOTE: For the items below in red surrounded with < >, see comments below for the actual information content, they are value substitutions from the previous command output!

    In the command prompt window that opens, type type the following commands one at a time, followed by the Enter key:

    IPCONFIG /ALL

    PING <computer_IP_address>

    PING <default_gateway_address>

    PING <dns_servers>

    PING 206.190.60.37

    PING yahoo.com

    Right click in the command window and choose Select All, then hit Enter to copy the contents to the clipboard.
    Paste the results in a message here.

    <computer_IP_address> - The IP Address of your computer, obtained from the IPCONFIG command above.

    <default_gateway_address> - The IP address of the Default Gateway, obtained from the IPCONFIG command above.

    <dns_servers> - The IP address of the first (or only) address for DNS Servers, obtained from the IPCONFIG command above.


    If you are on a machine with no network connection, use a floppy, USB disk, or a CD-RW disk to transfer a text file with the information to allow pasting it here.
     
  7. Curly

    Curly

    Joined:
    Apr 1, 2002
    Messages:
    1,249
    As JohnWill has said, maybe the WAP has died. Or your wireless adapter is not functioning properly.
     
  8. Sponsor

As Seen On
As Seen On...

Welcome to Tech Support Guy!

Are you looking for the solution to your computer problem? Join our site today to ask your question. This site is completely free -- paid for by advertisers and donations.

If you're not already familiar with forums, watch our Welcome Guide to get started.

Join over 733,556 other people just like you!

Loading...
Thread Status:
Not open for further replies.

Short URL to this thread: https://techguy.org/850823

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice